Derale-performance GM V8 4 & 6 Pass Dual Circuit Tube & Fin C Manuel d'utilisateur télécharger pdf

Installation Instructions for Engine Oil Cooler Kit’s #15902 & 15903

Installation Hints

1. The oil cooler core relies on airflow to provide heat dissipation. The best cooler location in the

vehicle is where the cooler will receive airflow from both vehicle motion and the cooling fan.

Ideally it should be mounted in front or behind the radiator but other locations with sufficient

airflow will also work. Be careful to protect the cooler from flying objects or any other moving

parts.

2. Keep rubber hoses away from sharp edges, hot exhaust and other wear points. Be careful not to

bend hose less than 5” radius (a small coffee can). Keep hose runs as short as possible but

always rough cut hose lengths 2” longer than measured for insurance

Thank you for buying our product.

Please read the following

Instructions in full before starting

the installation.

Sandwich Adapter Installation

Sandwich adapter fits between oil filter and engine

block. Before removing oil filter, check clearance

between filter and any obstructions such as frame

rail or exhaust pipe. The adapter is 1 3/4:” thick so

you will need at least 2 1/4” of clearance. If there

is insufficient clearance is found, refer to chart

below for a shorter length filter.

6 Remove oil filter and clean oil off engine

block mounting surface.

7 Install brass hose barbs on adapter

casting. Use Teflon tape to seal threads.

8 Take the five threaded sleeve-nuts. Find

the sleeve-nut that will thread into your oil

filter, this is the one to use.

9 Set the o-ring supplied onto the sandwich

adapter. Apply a light coat of engine oil to

o-ring seal. Slide sleeve-nut into adapter

and install on engine with o-ring facing

engine block. Adapter can be rotated for

ideal hose routing location. Torque sleeve-

nut to 20 foot pounds.

Install oil filter.

SIZE COLOR O.D.

FILTER

HEIGHT

FRAM

P.N.

FILTER

HEIGHT

FRAM P.N.

18MM X 1.5 WHITE 3" 4 15/16" PH3535 3 11/32" PH3387A

20MM X 1.5 BLACK 3" 4 15/16" PH2649A 3 23/64" PH3593A

22MM X 1.5 GREEN 3" 4 15/16" PH3750 3 63/64" PH2

3/4-16 YELLOW 3" 4 15/16" PH3600 3 23/64" PH3614

13/16-16 BLUE 3" 4 15/16" PH3429 3 23/64" PH3506

NOTE: THE O.E.M. SIZE FILTER WILL WORK IN

MOST APPLICATIONS EXCEPT IN APPLICATIONS

WITH VERY TIGHT CLEARENCES. SEE CHART

BELOW FOR

POSSIBLE OTHER FILTER

OPTIONS.

1 2

Résumé du contenu

Page 1 - Installation Hints

Installation Instructions for Engine Oil Cooler Kit’s #15902 & 15903 Installation Hints 1. The oil cooler core relies on airflow to p

Page 2 - Website: www.derale.com

Oil Cooler Installation 1. Using hose clamps supplied, attach the two ends of the hose to the cooler inlets (cooler core will flow in bo

Commentaires sur ces manuels

Pas de commentaire

Derale-performance GM V8 4 & 6 Pass Dual Circuit Tube & Fin C Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Chaudière à eau Derale-performance GM V8 4 & 6 Pass Dual Circuit Tube & Fin C. Derale Performance GM V8 4 & 6 Pass Dual Circuit Tube & Fin Cooler User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Chaudière à eau Derale-performance GM V8 4 & 6 Pass Dual Circuit Tube & Fin C