Derale-performance 5 Row Series 9000 Plate & Fin Transmission Coo Manuel d'utilisateur télécharger pdf

KIT CONTENTS

QTY. DESCRIPTION

1 Transmission Cooler

1 11/32” X 4’ Hose

4 Hose Clamps

1 Insta-dapt Adapter

Please read these instructions completely before starting the installation.

13611-13614-InstructionSheet

TOOLS NEEDED

Standard Screw Driver

or 5/16” Nut Driver

Dyke Pliers

Razor Knife

QTY. DESCRIPTION

2 NPT x 3/8”

4 Mounting Rods

4 Mounting Clips

4 Foam Pads

1/2” Barb Fittings

1x1

INSTALLATION INSTRUCTIONS

TRANSMISSION COOLER

PART # 13611-13614

(Continues on Page 2)

The Transmission Cooler can be mounted in multiple locations on your

vehicle. Reference Diagram # 2 for possible cooler positions. #1 is the

ideal location, #2 is second best and #4 being the last choice.

The Cooler core will flow in either direction, there is no specified inlet

or outlet port.

Note:

Diagram #2

COOLER INSTALLATION

(See Diagram #3)

1. Identify the 4 Mounting Rods, 4 Mounting Clips and

4 1x1 Foam Pads.

2. One by one, Install the 4 Mounting Rods thru the Transmission

Cooler.

3. Take the 1x1 Foam Pads supplied, peel off the paper lining & slide

them onto the Mounting Rods, sticking them against the

Transmission Cooler.

4. Take the Cooler Assembly with attached looped hose and hold in

the desired location.

5. Install the 4 Mounting Rods thru the Radiator/Condenser core.

Do not use excessive force when pushing the Mounting

Rods through the Radiator/Condenser. Excessive force could

cause damage to the fins and possibly puncture a tube.

6. Take the Mounting Clips supplied, making sure they are in the

correct direction (Derale writing out) install onto the Mounting Rods

and cinch them until the 1x1 Foam Pads are slightly compressed.

7. Cut off any excess Mounting Rods.

Mounting

Warning:

COOLER LOCATION

When selecting the best location for your vehicle, always consider a

location that will deliver the maximum airflow. (See Diagram #2)

PRE-INSTALLATION

ecure in place using the Hose Clamps.

1. Identify the two 1/2” NPT x 3/8” Barb Fittings.

2. Using Teflon Tape or suitable sealant, install the two 1/2” NPT x 3/8” Barb

Fittings onto the Transmission Cooler.

3. Identify the 11/32” X 4’ Hose and Hose Clamps.

4. Slide one hose clamp on each end of the supplied Hose.

5. Using a dab of oil, lubricate each end of the hose and install hose onto

the cooler inlets forming a loop.

6. S

This kit includes an Insta-dapt Adapter fitting for adapting the cooler

line to the radiator. (See Diagram #1)

The Insta-dapt fitting has a 1/2”-20 Male/Female thread and fits most

vehicles with 5/16” transmission cooler lines.

For vehicles that are not compatible with the Insta-dapt Adapter, please

reference Radiator Adapter Fitting Guide included.

IMPORTANT

Insta-dapt Adapter

Diagram #1

4’ Hose

Diagram #3

Foam Pads

Mounting

Clips

Mounting

Rods

5/8” Open End Wrench

7/8” Open End Wrench

Teflon Tape

Derale Performance, Los Angeles, CA 800.421.6288 www.derale.com

1 2 3

Résumé du contenu

Page 1 - PART # 13611-13614

KIT CONTENTSQTY. DESCRIPTION1 Transmission Cooler1 11/32” X 4’ Hose4 Hose Clamps1 Insta-dapt AdapterPlease read these instructions completely before s

Page 2 - Diagram #4

Warning: Installation of accessories should only be undertaken by those with mechanical knowledge and are familiar with working onvehicles. Always use

Page 3

RADIATOR ADAPTER FITTING GUIDE

Commentaires sur ces manuels

Pas de commentaire

Derale-performance 5 Row Series 9000 Plate & Fin Transmission Coo Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Chaudière à eau Derale-performance 5 Row Series 9000 Plate & Fin Transmission Coo. Derale Performance 5 Row Series 9000 Plate & Fin Transmission Cooler Kit User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Chaudière à eau Derale-performance 5 Row Series 9000 Plate & Fin Transmission Coo