Derale-performance Thermostatic Sandwich Adapter Kit with 3__8" Manuel d'utilisateur télécharger pdf

15730-15732-15733-15734-InstructionSheet

Derale Performance, Los Angeles, CA 800.421.6288 www.derale.com

INSTALLATION INSTRUCTIONS

ENGINE SANDWICH ADAPTER KIT

PART # 15730, 15732, 15733 & 15734

Please read these instructions completely

before beginning installation

KIT CONTENTS

QTY. DESCRIPTION

1 Sandwich Adapter

1 O-ring

2 3/8” NPT x 1/2” Barb Fittings

1 Sleeve Nut

IMPORTANT

In most cases the Factory Oil Filter will work with the

supplied sandwich adapter. In some applications where

the frame or exhaust system interferes with the new

filter depth we recommend using a shorter filter length.

See the chart below for possible filter options.

SLEEVE NUT

Colored Label

FRAM WIX FRAM WIX

THREAD LABEL FILTER FRAM FILTER WIX FILTER FRAM FILTER WIX

SIZE COLOR HEIGHT P/N HEIGHT P/N HEIGHT P/N HEIGHT P/N

3/4-16 YELLOW

18mm x 1.5 WHITE

20mm x 1.5 BLACK

22mm x 1.5 GREEN

4.92 PH3600 4.83 51516 3.34 PH3614 3.4 51348

4.94 PH3980 4.83 51036 3.36 PH3387A 3.4 51040

3.47 PH7317 N/A N/A 3.39 PH3593A 3.14 51381

4.94 PH3750 4.57 57026 3.98 PH2 3.43 57060

Diagram #1

VERIFYING SLEEVE NUT THREAD SIZE

Included in this kit should be a sleeve nut with thread specification as indicated

by the part number purchased and the product packaging. The thread size can

be verified by screwing the male end of the Sleeve Nut into the new or old engine

oil filter. If it is incorrect, please contact your dealer.

SANDWICH ADAPTER INSTALLATION

The Sandwich Adapter fits between the oil filter and the engine block. Before

removing the oil filter, check the clearance between the bottom of the filter and

the closest vehicle obstruction. If there are none, then proceed with the

installation. If you determine that the stock filter will not fit, refer to the Filter Chart

for alternative filter heights.

1. Remove the factory oil filter from the vehicle.

2. Remove the colored label from the Sleeve Nut (If there is one).

3. Take the Sandwich Adapter and the two Hose Barb Fittings provided. Using

Teflon Tape or a suitable sealant, screw the Hose Barb Fittings clockwise into

the Sandwich Adapter until snug. (See Diagram #2)

4. Using a wrench tighten the two Hose Barb Fittings.

5. Take the O-ring provided, apply a thin film of oil and install into the O-ring

groove on the Sandwich Adapter. (See Diagram #2)

Diagram #2

6. Making sure the engine block filter landing is clean from oil and dirt, take the Sleeve Nut, Sandwich Adapter, O-ring, and

install onto engine sliding the Sleeve Nut thru the Sandwich Adapter. Turn sleeve nut clockwise onto the engines filter

nipple. (See Diagram #2)

7. Using a torque wrench, torque the Sleeve Nut to 20 ft. lbs.

1. Install both ends of the hose onto the Hose Barb Fittings, forming a loop.

2. Take the looped end and route the hose to the oil cooler making sure to stay clear of sharp objects, exhaust systems, etc.

All bends in hose need to have a minimum radius of 5” or the diameter of a small coffee can.

3. Cut and attach hoses to the oil cooler. Secure hoses using zip ties.

1. Before starting the vehicle, check engine oil level and add accordingly.

2. Always check fluid levels on a flat surface.

3. After installation and vehicle has completely warmed up, recheck fluid level and inspect all connections for leaks.

ROUTING HOSES (HOSE SOLD SEPARATELY)

SYSTEM CHECK

Note:

Warning: Installation of accessories should only be undertaken by those with mechanical knowledge and are familiar with working on

vehicles. Always use eye protection (goggles, safety glasses or shield). Park the vehicle in a well lit area, on level ground and apply the

parking brake. Only work on a cold vehicle that has been sitting overnight, failure to do so will result in severe burns and injury. Before starting

the vehicle, make sure no tools or any other items are left under hood that could interfere with or be drawn into moving parts of the engine.

Failure to follow instructions can lead to severe damage and personal injury.

Résumé du contenu

Page 1 - ENGINE SANDWICH ADAPTER KIT

15730-15732-15733-15734-InstructionSheetDerale Performance, Los Angeles, CA 800.421.6288 www.derale.comINSTALLATION INSTRUCTIONSENGINE SANDWICH ADA

Plus de documents pour Capteurs Derale-performance Thermostatic Sandwich Adapter Kit with 3__8"

Voir le document Derale-performance Thermostatic Sandwich Adapter Kit with 3__8" Manuel d'utilisateur

Derale-performance Thermostatic Sandwich Adapter Kit with 3__8" Manuel d'utilisateur (1 pages)

Commentaires sur ces manuels

Pas de commentaire

Derale-performance Thermostatic Sandwich Adapter Kit with 3__8" Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Capteurs Derale-performance Thermostatic Sandwich Adapter Kit with 3__8" . Derale Performance Thermostatic Sandwich Adapter Kit with 3__8" NPT Ports and 18x1.5mm Filter Thread User Manual Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Capteurs Derale-performance Thermostatic Sandwich Adapter Kit with 3__8"

Commentaires sur ces manuels

Produits connexes et manuels pour Capteurs Derale-performance Thermostatic Sandwich Adapter Kit with 3__8"

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Capteurs Derale-performance Thermostatic Sandwich Adapter Kit with 38" . Derale Performance Thermostatic Sandwich Adapter Kit with 38" NPT Ports and 18x1.5mm Filter Thread User Manual Manuel d'utilisatio