Derale-performance Non-Thermostatic Universal Sandwich Adapter Kit wi Manuel d'utilisateur télécharger pdf

15702-InstructionSheet

Derale Performance, Los Angeles, CA 800.421.6288 www.derale.com

INSTALLATION INSTRUCTIONS

ENGINE SANDWICH ADAPTER KIT

PART # 15735

Please read these instructions completely

before beginning installation

KIT CONTENTS

QTY. DESCRIPTION

1 Sandwich Adapter

1 O-ring

2 ½” NPT x ½” Barb Fittings

1 3/4-16 Sleeve Nut (Yellow)

QTY. DESCRIPTION

1 13/16-16 Sleeve Nut (Blue)

1 18mm Sleeve Nut (White)

1 20mm Sleeve Nut (Black)

1 22mm Sleeve Nut (Green)

IMPORTANT

In most cases the Factory Oil Filter will work with the

supplied sandwich adapter. In some applications where

the frame or exhaust system interferes with the new

filter depth we recommend using a shorter filter length.

See the chart below for possible filter options.

SLEEVE NUT

Colored Label

FRAM WIX FRAM WIX

THREAD LABEL FILTER FRAM FILTER WIX FILTER FRAM FILTER WIX

SIZE COLOR HEIGHT P/N HEIGHT P/N HEIGHT P/N HEIGHT P/N

3/4-16 YELLOW

13/16-16 BLUE

18mm x 1.5 WHITE

20mm x 1.5 BLACK

22mm x 1.5 GREEN

4.94 PH3600 4.83 51516 3.35 PH3614 3.40 51348

4.94 PH3429 4.83 51045 3.35 PH3506 3.40 51042

4.94 PH3980 4.83 51036 3.35 PH3387A 3.40 51040

3.50 PH7317 3.50 51356 3.35 PH3593A 3.19 51334

4.94 PH3750 4.57 57026 4.00 PH2 4.34 51258

Diagram #1

SANDWICH ADAPTER INSTALLATION

The Sandwich Adapter fits between the oil filter and the engine block. Before

removing the oil filter, check the clearance between the bottom of the filter and

the closest vehicle obstruction. If there are none, then proceed with the

installation. Otherwise, the Sandwich Adapter is 1-3/4” Thick, so you will need 2”

more clearance then stock. If you determine that the stock filter will not fit, refer

to the Filter Chart for alternative filter heights.

1. Remove the factory oil filter from the vehicle.

2. Take the 5 Sleeve Nuts provided, each Sleeve Nut has a Color coded label

(See Diagram #1). For your reference, the filter chart above will tell you the

thread size colors. The colors are only needed if: 1. You know the specific

thread size of your vehicle or 2. You need to use the filter chart to determine

an alternate filter to use. Using the old oil filter take each Sleeve Nut and

determine which Sleeve Nut matches the oil filter by screwing the Sleeve Nut

into the oil filter. Once you have determined the correct size, disregard the 4

other sizes.

3. Remove the colored label from the Sleeve Nut.

Diagram #2

4. Take the Sandwich Adapter and the two Hose Barb Fittings provided. Using Teflon Tape or a suitable sealant, screw the

Hose Barb Fittings clockwise into the Sandwich Adapter until snug. (See Diagram #2)

5. Using a wrench tighten the two Hose Barb Fittings.

6. Take the O-ring provided, apply a thin film of oil and install into the O-ring groove on the Sandwich Adapter. (See Diagram #2)

7. Making sure the engine block filter landing is clean from oil and dirt, take the Sleeve Nut, Sandwich Adapter, O-ring, and

install onto engine sliding the Sleeve Nut thru the Sandwich Adapter. Turn sleeve nut clockwise onto the engines filter nipple.

8. Using a torque wrench, torque the Sleeve Nut to 20 ft. lbs.

1. Install both ends of the hose onto the Hose Barb Fittings, forming a loop.

2. Take the looped end and route the hose to the oil cooler making sure to stay clear of sharp objects, exhaust systems, etc.

All bends in hose need to have a minimum radius of 5” or the diameter of a small coffee can.

3. Cut and attach hoses to the oil cooler. Secure hoses using zip ties.

1. Before starting the vehicle, check engine oil level and add accordingly.

2. Always check fluid levels on a flat surface.

3. After installation and vehicle has completely warmed up, recheck fluid level and inspect all connections for leaks.

ROUTING HOSES (HOSE SOLD SEPARATELY)

SYSTEM CHECK

Note:

Warning: Installation of accessories should only be undertaken by those with mechanical knowledge and are familiar with working on

vehicles. Always use eye protection (goggles, safety glasses or shield). Park the vehicle in a well lit area, on level ground and apply the

parking brake. Only work on a cold vehicle that has been sitting overnight, failure to do so will result in severe burns and injury. Before starting

the vehicle, make sure no tools or any other items are left under hood that could interfere with or be drawn into moving parts of the engine.

Failure to follow instructions can lead to severe damage and personal injury.

(See Diagram #2)

Résumé du contenu

Page 1 - PART # 15735

15702-InstructionSheetDerale Performance, Los Angeles, CA 800.421.6288 www.derale.comINSTALLATION INSTRUCTIONSENGINE SANDWICH ADAPTER KITPART # 15735P

Commentaires sur ces manuels

Pas de commentaire

Derale-performance Non-Thermostatic Universal Sandwich Adapter Kit wi Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Capteurs Derale-performance Non-Thermostatic Universal Sandwich Adapter Kit wi. Derale Performance Non-Thermostatic Universal Sandwich Adapter Kit with 1_2" NPT Ports User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Capteurs Derale-performance Non-Thermostatic Universal Sandwich Adapter Kit wi